DuPont™ Thermax™ Sheathing Insulation
Nonstructural, Glass-Fiber-Infused Rigid Polyiso Insulation
DuPont™ Thermax™ Sheathing Insulation
Nonstructural, Glass-Fiber-Infused Rigid Polyiso Insulation
<br><b>DuPont™ Thermax™ Sheathing Polyisocyanurate Insulation</b> is a non-structural, rigid board insulation consisting of a glass-fiber-infused polyisocyanurate foam core laminated between 1 mil smooth, reflective aluminum facers on both sides. The glass-fiber reinforcement contributes to improved fire performance and dimensional stability.
<br><br>
<b>Thermax™ Sheathing Insulation</b> also offers high, long-term thermal resistance, with facers that help prevent water and water vapor intrusion into the insulation foam allowing it to stabilize at a higher R-value. In the USA, Thermax™ Sheathing can be installed as exterior continuous insulation and also installed exposed to the interior without a thermal barrier. Used in conjunction with the appropriate joint closure system for the application, Thermax™ Sheathing – with its low perm rating – can help to reduce moisture condensation within and behind the insulation.
Features & Benefits
Specifications
Standard Sizes
| Thickness | Width | Length | R-Value | Edge Treatment |
|---|---|---|---|---|
| 1/2 in. | 4 ft. | 8 ft. | 3.3 | Square Edge |
| 3/4 in. | 4 ft. | 8 ft. | 5.0 | Square Edge |
| 1.0 in. | 4 ft. | 8 ft. | 6.8 | Square Edge |
| 1 1/2 in. | 4 ft. | 8 ft. | 9.8 | Square Edge, Shiplap |
| 2.0 in. | 4 ft. | 8 ft. | 13.0 | Square Edge, Shiplap |
| 2 1/2 in. | 4 ft. | 8 ft. | 15.8 | Square Edge, Shiplap |
| 3.0 in. | 4 ft. | 8 ft. | 18.6 | Square Edge, Shiplap |
| 3 1/2 in. | 4 ft. | 8 ft. | 21.3 | Square Edge, Shiplap |
| 4.0 in. | 4 ft. | 8 ft. | 24.0 | Square Edge, Shiplap |
Note: Please be advised that additional sizes may be available. Availability of all sizes varies by region and is subject to change. For further information, please contact your local DuPont Sales Representative or call us at 1-866-338-7668.
Testing
<b>Thermax™ Sheathing Insulation</b> exhibits the properties and characteristics indicated in the table below when tested as represented. Review all instructions and (Material) Safety Data Sheet ((M)SDS) before use. Please contact DuPont at 1-833-338-7668 when additional guidance is required for writing specifications that include this product.
| TEST METHOD | TEST TITLE | PROPERTY | RESULTS |
|---|---|---|---|
| FIRE | |||
| UL 723 | Test Method for Surface Burning Characteristics of Building Materials | Surface Burning Characteristics1 | Flame Spread ≤ 25 Smoke Developed ≤ 450 Core and Finished Product |
| NFPA 285 | Standard Fire Test Method for Evaluation of Fire Propagation Characteristics of Exterior Wall Assemblies Containing Combustible Components | Fire Progagation - Exterior2 | Pass |
| UL 1715 | Standard for Safety Fire Test of Interior Finish Material | Fire Progagation - Interior | Pass |
| NFPA 286 | Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth | Fire Progagation - Interior | Pass |
| NFPA 268 | Standard Test Method for Determining Ignitability of Exterior Wall Assemblies Using a Radiant Heat Energy Source | Ignitabiilty - Exterior | Pass |
| THERMAL | |||
| ASTM C518 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus | Thermal Resistance 1 inch @ 75°F mean temp3 | 6.9 ft2 •h•°F/Btu, R-value, min. |
| ASTM D2126 | Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging | Dimensional Stability | 0.2% linear (length & width) |
| STRENGTH | |||
| ASTM D1621 | Standard Test Method for Compressive Properties of Rigid Cellular Plastics | Compressive Strength4 | 25 psi |
| ASTM C203 | Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation | Flexural Strength | 75 psi |
| ASTM D1623 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics | Tensile Strength | 500 psf, min. |
| AIR | |||
| ASTM E2178 | Standard Test Method for Determining Air Leakage Rate and Calculation of Air Permeance of Building Materials | Rate of Leakage | <0.001 L/s*m2, max |
| ASTM E2357 | Standard Test Method for Determining Air Leakage Rate of Air Barrier Assemblies | Air Leakage | No Leakage |
| ASTM E283 | Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Skylights, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen | Rate of Leakage | <0.02 L/s*m2, max |
| WATER | |||
| ASTM E96 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials | Water Vapor Permeance. | 0.01 perm |
| ASTM C209 | Standard Test Methods for Cellulosic Fiber Insulating Board | Water Absorption | 0.1% volume, max. |
| ASTM E331 | Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference | Water Penetration | Pass |
1Calculated flammability values for this or any other material are not intended to represent hazards that may be present under actual fire conditions.
2See Jensen Hughes engineering judgement
3R-value of 1.0-inch of foam measured @ 75°F mean temperature, determined in accordance with ASTM C518 after aging for 90 days @ 140°F.
4Vertical compressive strength is measured at 10 percent deformation or at yield, whichever occurs first.